zj center console lid cup holders
07-04-2011, 04:04 PM
#1
CF Veteran
Thread Starter
Join Date: Nov 2008
Location: mass
Posts: 1,021
Likes: 0
Received 3 Likes
on
2 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 high output
zj center console lid cup holders
i was in my Buddy's grand Cherokee yesterday and noticed the center console lid has cup holders.
It looked like you could probably pull the Cherokee lid off and swap in the zj one. anyone ever do this? I'm gonna go to the junkyard tomorrow and test out my theory.
It looked like you could probably pull the Cherokee lid off and swap in the zj one. anyone ever do this? I'm gonna go to the junkyard tomorrow and test out my theory.
07-04-2011, 09:49 PM
#4
Senior Member
Join Date: Feb 2011
Location: Apollo, PA
Posts: 517
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1996
Model: Cherokee
Engine: 4.0
Originally Posted by 01cherokeexj
I saw a thread the other day where someone did exactly that. So it is possible, I just don't know how.
Sent from my DROID INCREDIBLE using Cherokee Forum
07-04-2011, 10:16 PM
#6
Member
Join Date: May 2011
Location: Gloucester, VA
Posts: 190
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1994
Model: Grand Cherokee
Engine: 5.2L
Here ya go, it was under the fab section >
https://www.cherokeeforum.com/f58/6-cup-holders-93958/
TylerL. 94 ZJ 3" lift. My DD.
https://www.cherokeeforum.com/f58/6-cup-holders-93958/
TylerL. 94 ZJ 3" lift. My DD.
07-04-2011, 10:32 PM
#7
CF Veteran
Thread Starter
Join Date: Nov 2008
Location: mass
Posts: 1,021
Likes: 0
Received 3 Likes
on
2 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 high output
That came out really good but its not really what I'm talking about. The zj lid has cup holders that slide out of the back.
Trending Topics
07-05-2011, 03:52 PM
#9
Senior Member
Join Date: Jul 2011
Location: Wilmington, NC
Posts: 598
Likes: 0
Received 1 Like
on
1 Post
Year: 1997
Model: Cherokee
Engine: 4.0L
I picked a lid up at the PnP today.
It is about 2" wider than the XJ one and will require some light fab work if you'd like to attach it to the console with something more than self threading screws through thin plastic (Which I am sure plenty will chime in and say works just fine).
It is about 2" wider than the XJ one and will require some light fab work if you'd like to attach it to the console with something more than self threading screws through thin plastic (Which I am sure plenty will chime in and say works just fine).
07-05-2011, 04:49 PM
#10
CF Veteran
Join Date: Feb 2010
Location: Oroville, CA
Posts: 12,367
Likes: 0
Received 19 Likes
on
18 Posts
Year: 1995
Model: Grand Cherokee
Engine: 4.0 with all of the noise and clatter
The 96 and up ZJ has the cup holders at the rear of the lid, but I think the lid is too wide for the XJ consol.
07-05-2011, 06:40 PM
#12
CF Veteran
Thread Starter
Join Date: Nov 2008
Location: mass
Posts: 1,021
Likes: 0
Received 3 Likes
on
2 Posts
Year: 1992
Model: Cherokee
Engine: 4.0 high output
Yea it is a little wider but looks like it belongs. If you look at the back the hindge( not on the lid side) is actually attached to metal and you can just use the zj hindge and drill new holes. I couldn't find a tan one so I'm gonna wait to do it. The latch my take some fabing.
