Oil leak around oil filter
#1
Oil leak around oil filter
I'm only writing this to confirm. I haven't seem this mentioned for newer(ish) Xj's. But I have a 1999. I have a oil leak around the oil filter. There is still the 3 O rings used in this year, right?
I also need to replace the valve cover gasket and oil pan. However I'm paying someone to do the oil pan. It looks too labor intensive for a single fella to do.
Thanks in advance
I also need to replace the valve cover gasket and oil pan. However I'm paying someone to do the oil pan. It looks too labor intensive for a single fella to do.
Thanks in advance
#2
CF Veteran
Join Date: Feb 2009
Location: Houston Tx.
Posts: 2,203
Likes: 0
Received 3 Likes
on
3 Posts
Year: 1995
Model: Cherokee
Engine: 4.0
You need to change out the O-rings on the oil filter adapter, it's not that hard.
And I will paying someone to do my oil pan gasket also as it can't be done without a lot of yelling and screaming of obscenities.
And I will paying someone to do my oil pan gasket also as it can't be done without a lot of yelling and screaming of obscenities.
#6
CF Veteran
Mine can be done on the ground thanks to the excessive lift. Stock xj I disconnect the shocks and let the axle droop. 1 man job takes about 2 hrs tops.
Trending Topics
#8
CF Veteran
#10
I agree. Then I hate myself a little bit too for not knowing. My friends all call me a smart @$$ b/c I know so much stuff. But you kinda have to since a lot of people you come across don't know and it's kinda their job to know.
But my reply to my friends is, "better to be a smart @$$ than a dumb @$$."
But my reply to my friends is, "better to be a smart @$$ than a dumb @$$."
#11
Senior Member
Join Date: Oct 2009
Location: Sutton, New Hampshire
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
Year: 1995
Model: Cherokee
Engine: 4.0L
#13
Ken1234
Okay so the oil filter adapter o-ring replacement. 95 XJ, 4.0 151k, I'd like to meet the engineering genious that thought up the " lets put a torx head bolt in an area that doesn't have enough space to put a socket on. Or better yet NO hex head to put a wrench on" What a S**T head.
And then let's top it off by making the bolt a dissimilar metal to the adapter just to make sure it corrodes.
Okay so I go to the dealer and get the o-rings and ask an older mechanic who's been there awhile (figure he's done a few) what the trick is to getting it loose? He says all you have to do is shock the bolt head with an air hammer that has a good sharp chisel, while turning on the torx. Sounds good to me. There was no chance of getting it loose I don't care how much it got shocked all it did was make a mess of the bolt head. Should have know better than that.
So here's what I did. I went back to the local dealer and got a new adapter and bolt (still a torx, nothings changed figures) already had the o-rings. I loaded a new 18 tooth metal blade on my electric sawz-all and opened a big can of sawz-all whoop *** on the adapter. First I tied back the positive cable and sending unit wires so I wouldn't hit them. And I cut off the top of the adapter behind the head of the bolt about 3/4's of an inch. Then I wiggled the adapter loose back and forth a little. (the roll pin behind it holds the adapter in position) so you only have a little play. Then I kept working the top of the be-headed bolt to loosen it and unthread it out. You can always notch out the side of the adapter to get more work room on the bolt. Once it's out piece of cake. Lube the o-rings with plenty of light oil. I also never-seized where the new bolt head contacts the adapter in I ever re-attack (doubtful though).
Tip? I noticed that the nipple that comes with the new adapter the one the filter screws onto, will screw into the block and probably be able to eliminate the adapter if you can find a skinny filter with the same o-ring and threads. (I'm thinking one off of another 4wd) But I didn't have time to mess with it, that and I already had the adapter new and couldn't return it. I'm attaching a pic of the results after the removal. saved a ton of headaches and cussin. The parts cost me total of $65.00 my time and aggravation is worth alot more than that. Thats my 2 cents. Good Luck ! How the heck do I attach a pic?
And then let's top it off by making the bolt a dissimilar metal to the adapter just to make sure it corrodes.
Okay so I go to the dealer and get the o-rings and ask an older mechanic who's been there awhile (figure he's done a few) what the trick is to getting it loose? He says all you have to do is shock the bolt head with an air hammer that has a good sharp chisel, while turning on the torx. Sounds good to me. There was no chance of getting it loose I don't care how much it got shocked all it did was make a mess of the bolt head. Should have know better than that.
So here's what I did. I went back to the local dealer and got a new adapter and bolt (still a torx, nothings changed figures) already had the o-rings. I loaded a new 18 tooth metal blade on my electric sawz-all and opened a big can of sawz-all whoop *** on the adapter. First I tied back the positive cable and sending unit wires so I wouldn't hit them. And I cut off the top of the adapter behind the head of the bolt about 3/4's of an inch. Then I wiggled the adapter loose back and forth a little. (the roll pin behind it holds the adapter in position) so you only have a little play. Then I kept working the top of the be-headed bolt to loosen it and unthread it out. You can always notch out the side of the adapter to get more work room on the bolt. Once it's out piece of cake. Lube the o-rings with plenty of light oil. I also never-seized where the new bolt head contacts the adapter in I ever re-attack (doubtful though).
Tip? I noticed that the nipple that comes with the new adapter the one the filter screws onto, will screw into the block and probably be able to eliminate the adapter if you can find a skinny filter with the same o-ring and threads. (I'm thinking one off of another 4wd) But I didn't have time to mess with it, that and I already had the adapter new and couldn't return it. I'm attaching a pic of the results after the removal. saved a ton of headaches and cussin. The parts cost me total of $65.00 my time and aggravation is worth alot more than that. Thats my 2 cents. Good Luck ! How the heck do I attach a pic?
#14
Im new to this fourm stuff. Ive got a 1995 se straight 6 with 199,400 miles. runs strong, only oil leak thats big enough to bother me is the only one not in the book haynes book it tells me nothing about how fix the oil leak around the filter (its not the filter seal its self). How do you go about replacing those 3 rings you guys are talking about. meaning how do i get off?
#15
CF Veteran
Join Date: Jul 2010
Location: Albuquerque
Posts: 1,208
Likes: 0
Received 1 Like
on
1 Post
Year: 1999
Model: Cherokee
Engine: 4.0
I just did the oil filter adapter o ring change about a month ago. I used socket caps. Bought a cheapo set from Harbor Freight for like $5. It was still a PITA, but they finally came off after about an hour of trying.